Уважаемые гуру:
имею следующую инфу по перепрограммированию:
NB: - Ensure that the floor is clean and free from cables etc.
- Before starting up the door, check that the buffers have been positioned correctly and that they are
properly fixed with the door correctly in balance. Incorrect balancing may lead to unsafe operation and
may shorten the life of the product.
- Installation can only be carried out using the set of buttons in the control box, not an external push
button box or radio control. If Electrical Door Lock System, put a jumper on X7:2-3 during the installation.
For doors with small drums and without safety features, there may be a risk of the wire unwinding.
Check therefore that the wire is located correctly on the drum.
The power SHALL be switched off-on before an installation!
1. Connect the installation device, X7:5 and 6.
2. Disengage the door, place it in a position 1.5m above
the floor and engage it.
Switch on the power.
3. Mark out a “1m position” above the floor on the door track.
4. SW1 ON.
5. Hold-to-run downwards (Up- or Down button) until the rubber sealing edge is in position
with the 1m mark. (Adjust with the Up/Down buttons).
The door is now stopped at the mark.
6a. Actuate the installation device with a short pressure.
6b. Place the installation device on the highest point of the floor below the door leaf.
(The lower sensing level of the device shall be activated by the door).
VL-drum:
7a. Push down.
The door moves slowly by impulse operation down, reverses against the lower level of the
device and opens to a fully open position.
SL, LL & HL-drum:
7b. Push down. The door moves slowly by impulse operation down to the floor and reverses.
When the top section of the door is in the middle of the rail bend
(where the cable reaches the straight drum part), push stop.
Push up. The door now moves by impulse operation to a fully open position.
NB! If the installation fails between points 1-7,
adjust the torque (force). See page 11.
8. SW1 OFF. (After 2 sec. the door is operable).
The installation is now complete. Please, see also “Check that” -points at page 10.
NOTE! This installation guide concerns the ECS 920 Control system for CDM 9.
The UP and DOWN buttons function: ”Mode 1” = Impulse UP and Hold to run DOWN
”Mode 2” = Hold to run UP and Hold to run DOWN
K047860 13 (16)
Installing and starting to use the ECS 920, ”Mode 2”
1. The door is installed and ready according to
”mode 1”.
2. Run the door to fully closed position by ”hold to run”
on the down button.
3. Press all the three (up, stop, down) buttons at the
same time, for min 6 seconds.
4. Release the buttons, you are now ready to operate
your door in hold to run function UP and DOWN!
NOTE!
In order to go back to “mode 1”, you have to make a
full installation according to ”Mode 1” again.
Check that:
Check that the door stops on instantaneous overload trip (on opening).
Check that all control devices are operational.
NOTE:
1. The two LED’s, D8 and D9 on the manoeuvring PCB, indicates the stop circuit.
If both are lit the stop circuit is ok.
2. The programmed installation is not lost when the power is cut.
3. After a power failure the door must always be restarted upward and run to the fully open position to regain
the hold-to-run mode down.
4. If anything is wrong, consult the trouble shooting guide.
Так же узнал что нужен K042698 Установочное устройство для блока управления 920
устройство подключается к разъёму Х1 контакты 12 и 13.(вместо х7, который указан в 1 пункте и на другие контакты вместо 5 и 6).
Только блин оно стоит почти 200евриков...
Есть идеи как его смастерить, с учетом той информации которая имеется? Фото во вложении.